Reset your Holosun EPS Carry Red Dot Sight

Wiki Article

Occasionally, you may need to reinitialize your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the adjustments or are experiencing unexpected behavior. Fortunately, resetting your Holosun is a straightforward process that can be achieved in just a few procedures.

• First ensuring your red dot sight is activated.
• Find the small reset button on the side of the device.
• Utilize a small object to activate the reset button for approximately three seconds.
• Let go the lever and your Holosun EPS Carry Red Dot sight will power cycle.
• Your red dot sight should now be returned to its factory settings.

Reset Your Holosun EPS Carry Red Dot toward Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to return to original, resetting it to its factory configuration is a breeze. First, locate the tiny button on the rear of your optic. Then, press and hold it for around twelve seconds until you see the red dot blink. Your Holosun EPS Carry is now reset to its factory settings, ready for consistent targeting.

Bring Your Holosun EPS Carry Back to Action

Is your beloved Holosun EPS Carry experiencing some issues? Don't despair! A simple factory reset can often fix the problem and get your red dot sight back to its former glory. Before you begin, remember to remove the battery from your Holosun EPS Carry to prevent unintended activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these simple steps:

• Simultaneously press and hold the power button for approximately 5 seconds.
• The display will flash, indicating that the reset is in progress.
• Release the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can insert the battery and confirm your sight's functionality. If you encounter any further problems, don't hesitate how to factory reset Holosun EPS Carry red dot to reach out to their technical assistance.

Restore Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Adhere to these steps carefully to ensure a successful factory reset.

• First, Energize your Holosun EPS Carry by pressing the power button.
• After that, press and hold both the mode button and the up/down adjustment button simultaneously.
• During continue holding these buttons, activate the power button once.
• A message will show a confirmation prompt indicating that the reset process is initiated.
• Permit the process to finish. This may take a few moments. Once done, your Holosun EPS Carry will automatically deactivate.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Erase All Settings on Your Holosun EPS Carry

To Default reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Turning a specific button combination. Consult your Guidebook for the exact button sequence for your model. Once in the settings menu, look for an option that says "Factory Default". Select this option and confirm the reset. Your sight will then power off and restart with all settings Restored to their default values.

Reinitialize your Holosun EPS Carry through a Factory Default Settings

If your Holosun EPS Carry is acting funny, a factory reset might be the answer. This will return your sight to its original settings, clearing any altered configurations you've made. To accomplish this reset, follow these easy steps:

• To begin, locate the reset button on your EPS Carry.
• Secondly, press a thin object, like a paperclip, to activate the reset button.
• As you hold the reset lever activated, turn your EPS Carry.
• The sight will blink a message confirming that the reset is successful.

Once the reset is complete, your EPS Carry will be set to its factory settings.

Report this wiki page